1
Fel efter test med Sandra 2004!
Postat av skuM_ den 9 Februari 2004, 01:18
5 kommentarer · 217 träffar
Jag testade detta program då jag tyckte att min dator ej funkade som den skulle och fick dessa felmedelande efter en test. Ni kan gärna rådgiva med vad jag skall göra för att få detta fixat. Är dock många fel och på engelska vilket jag är kass på ;(
#1: Large memory modules (256MB or greater) should be Registered/Buffered, especially if more than 2 are installed on the same channel. This improves signal quality by reducing the load on the chipset channel. While these modules add an extra clock delay due to the on-board buffers (thus CL2 effectively becomes CL3), the stability will be worth it. Server chipsets with many memory slots generally require Registered memory.
Fix: If you plan on adding more memory, consider replacing the modules with Registered/Buffered modules. Do note that you cannot mix Unbuffered and Registered/Buffered modules on the same channel, but you may be able to if the chipset has multiple memory channels.
#2: Warning W2518 - Mainboard temperature is too high (i.e. over 50ºC). This should appear only if the mainboard has a temperature-monitoring sensor installed.
Fix: Power down the system immediately. Open the case and check that all the fans are working and check whether components are unusually hot inside. Make sure the components have good all-round ventilation. Use more fans if required.
#3: Warning W2519 - One of the mainboard fans has failed or is spinning too slowly. This should appear only if the mainboard has a temperature-monitoring sensor installed and the fans have tachometers. If the fan is speed controlled, this may be normal.
Fix: If the fan is not speed controller, power down the system immediately. Open the case and check that all the fans are working and check whether components are unusually hot inside. Make sure the components have good all-round ventilation.
#4: Warning W216 - The CPU fan has failed. This should appear only if the CPU has a fan with tachometer installed, connected correctly to the main board data capturing chip.
Fix: Power down your system immediately. Open the case and check that the CPU fan is working and the heat sink is not unusually hot. Make sure the CPU has good all-round ventilation.
#5: Warning W236 - Processor Vcore higher than rated maximum. Unless the reported value is incorrect or the processor is a different type that is not correctly detected, the voltage is higher than it should be. If you’re over-clocking the processor you may have pushed too far.
Fix: If the BIOS supports processor Vcore setting, check that the voltage programmed is correct for the processor installed. If not, check whether the mainboard supports the installed processor.
Skulle vara väldigt tacksam ifall ni hjälpte mig på ett lätt och förstående sätt så jag kan lösa detta. Jag vet dock ej om programmet har visat fel eller så men detta är vad som stod efter en test. Nedan står mina dator komponenter.
Tack och inget whine eller nått... svara bara om ni vet nått. Påhopp rapporteras.
_____________ _____
AMD XP2600+ || TwinMOS 512DDR PC3200 || Asus A7N8X deluxe/Golden nForce2 || Hitachi Deskstar 7K250 120GB || Sapphire Radeon 9600pro 128MB || Samsung 957p "19 || Allt oklockat!
#1: Large memory modules (256MB or greater) should be Registered/Buffered, especially if more than 2 are installed on the same channel. This improves signal quality by reducing the load on the chipset channel. While these modules add an extra clock delay due to the on-board buffers (thus CL2 effectively becomes CL3), the stability will be worth it. Server chipsets with many memory slots generally require Registered memory.
Fix: If you plan on adding more memory, consider replacing the modules with Registered/Buffered modules. Do note that you cannot mix Unbuffered and Registered/Buffered modules on the same channel, but you may be able to if the chipset has multiple memory channels.
#2: Warning W2518 - Mainboard temperature is too high (i.e. over 50ºC). This should appear only if the mainboard has a temperature-monitoring sensor installed.
Fix: Power down the system immediately. Open the case and check that all the fans are working and check whether components are unusually hot inside. Make sure the components have good all-round ventilation. Use more fans if required.
#3: Warning W2519 - One of the mainboard fans has failed or is spinning too slowly. This should appear only if the mainboard has a temperature-monitoring sensor installed and the fans have tachometers. If the fan is speed controlled, this may be normal.
Fix: If the fan is not speed controller, power down the system immediately. Open the case and check that all the fans are working and check whether components are unusually hot inside. Make sure the components have good all-round ventilation.
#4: Warning W216 - The CPU fan has failed. This should appear only if the CPU has a fan with tachometer installed, connected correctly to the main board data capturing chip.
Fix: Power down your system immediately. Open the case and check that the CPU fan is working and the heat sink is not unusually hot. Make sure the CPU has good all-round ventilation.
#5: Warning W236 - Processor Vcore higher than rated maximum. Unless the reported value is incorrect or the processor is a different type that is not correctly detected, the voltage is higher than it should be. If you’re over-clocking the processor you may have pushed too far.
Fix: If the BIOS supports processor Vcore setting, check that the voltage programmed is correct for the processor installed. If not, check whether the mainboard supports the installed processor.
Skulle vara väldigt tacksam ifall ni hjälpte mig på ett lätt och förstående sätt så jag kan lösa detta. Jag vet dock ej om programmet har visat fel eller så men detta är vad som stod efter en test. Nedan står mina dator komponenter.
Tack och inget whine eller nått... svara bara om ni vet nått. Påhopp rapporteras.
_____________ _____
AMD XP2600+ || TwinMOS 512DDR PC3200 || Asus A7N8X deluxe/Golden nForce2 || Hitachi Deskstar 7K250 120GB || Sapphire Radeon 9600pro 128MB || Samsung 957p "19 || Allt oklockat!
